0
Owner's of the Canon Camera Accessories TC80N3 gave it a score of 0 out of 5. Here's how the scores stacked up:
4 5 6
Interval Timer Mode (continued)
3. To pause the interval timer, press the Start/Stop button. Press
it again to resume.
Note: The interval you select must be longer than than the
combined time of the shutter speed and shutter recocking time,
otherwise the result will be continuous shooting.
When you are shooting with electronic ash the time interval
you set must be longer than the ash recycle time. If the time
interval is less than the recycle time the shutter will not release
until the ash unit has recycled. With Canon Speedlites that have
the Save Energy (SE) feature, the ash will automatically recycle
one minute before the exposure.
Long Exposure Mode
1. You must set the
camera's shutter to Bulb (B),
otherwise the camera will
shoot continuously until the
exposure time you have set
expires or you run out of exposures, whichever comes rst.
2. Use the Jog Dial to set the desired exposure time.
3. Press the Start/Stop button. The exposure will start, the icon
will blink and the exposure time will begin to count down.
4. To cancel the exposure, press the Start/Stop button.
Note: For unattended shooting, focus manually. If the camera is
set to AF and is unable to nd focus it may not release the shutter.
Exposure Count
1. Press the Mode Button
to select the Exposure
Count mode.
2. Press the Jog Dial. The
exposure count digits will
begin to blink.
3. Turn the Jog Dial to the number of exposures you want, from
1 to 99. If you set the counter to 00, the number of exposures
will limited only by the amount of lm or memory card space
available.
4. Press the Jog Dial to register the number of exposures. Once
an amount has been registered the exposure count display
will no longer blink.
5. Press the Start/Stop button. The camera will begin shooting
and will continue until it completes the number of exposures
you have. The TC-80N3 will count down the number of
exposures. Unless you specify a specic interval, the exposures
will be taken at one-second intervals.
Note: When shooting a sequence of exposures with ash, set
the interval timer so that the ash will have enough time to recyle
between exposures.
Hold Function
The Hold function prevents accidental changes to your settings. It
also prevents the Start/Stop Button from accidentally stopping an
operation after it has started. To activate this function, press and
hold the Display Illuminator Button for at least three seconds until
the Hold indicator appears on the display. To cancel this function,
press and hold the Display Illuminator Button for at least three
seconds until the Hold indicator disappears.
Cancelling the Settings
Simultaneously press the Mode Button, Display Illuminator Button
and Jog Dial to cancel all settings. Setting the time or number of
exposures to 0 will cancel the respective mode.
Remote Switch Function
The TC-80N3's Release Button functions in the same way as the
Remote Switch RS-80NC. The remote switch function does not
require battery power.
As with your camera's shutter button, you can press the
Release Button either halfway or all the way. Pressing it halfway
activates your camera's autofocus and exposure meter. Pressing
it all the way will release the shutter.
For long exposures or continuous shooting, press the
Release Button completely and slide it forward, in the direction
of the Running Lock Arrow. This will lock the button in the fully
depressed position. To release the button, slide it back to its
original position.
Note: Even when the Interval Mode or Self-timer are active, you
can still take a picture immediately by pressing the Release But-
ton or your camera's shutter button. Also note that the timing or
exposure count mode you have set will not be affected if you use
the Release Button. During a long exposure that is controlled by
the TC-80N3, however, the release button will be inoperable.
ST INT LE EXP Description
• Self-timer operates
• Interval time operates
• Shutter opens for extended
time
• The set number of exposures is
taken at one-second intervals.
• • After the self-timer delay the
interval timer begins
• • After the self-timer delay the
long exposure begins
• •
After the self-timer delay the set
number of exposures is taken
at one-second intervals
• • The long exposure is taken at
the set intervals
• • The set number of exposures is
taken at the set intervals
• • •
After the self-timer delay the
long exposure is taken at the
set intervals
• • •
After the self-timer delay the set
number of exposures is taken
at the set intervals
• • •
The set number of long
exposures is taken at the set
intervals
• • • •
After the self-timer delay the set
number of long exposures is
taken at the set intervals
• •
This is an incompatible com-
bination. The timer will default
to long exposure only.
• • •
This is an incompatible com-
bination. The timer will default
to self-timer delay followed by
long exposure
Timer Mode Combinations
Find Your Products By Category
Please Login
